Water Heater Pilot Light Won’t Stay Lit? Causes and Fixes

Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

If your water heater’s pilot light won’t stay lit, the most common cause is a faulty or misaligned thermocouple, the small safety sensor that keeps the gas valve open only while it senses the flame. Other causes include a dirty pilot tube, drafts, low gas supply, a clogged air intake on newer heaters, or a failing gas control valve. A thermocouple is a cheap part that many homeowners can replace in about an hour, but if you smell gas or the pilot keeps failing after a couple of tries, call a professional.

Safety first

  • Smell gas (rotten eggs)? Don’t relight anything or use switches. Leave the house and call your gas company from outside.
  • Follow the lighting label on your heater; steps vary by model.
  • Stop after a couple of failed attempts and call a licensed technician rather than repeating it over and over.
  • Turn the gas off before cleaning or replacing any parts.

Why does my pilot light keep going out?

Symptom Likely cause Fix
Pilot lights but goes out as soon as you release the knob Faulty, dirty or misaligned thermocouple Make sure the thermocouple tip sits in the flame; replace it if it still fails
Weak, small or yellow flame Dirty or clogged pilot tube or orifice Gas off, then clean the pilot opening gently with compressed air or a thin brush
Pilot goes out randomly Drafts from doors, windows, vents or HVAC Block drafts; keep the area around the heater clear
Pilot won’t light at all Gas supply off or low; failed igniter Check other gas appliances and the supply valve; replace the igniter
Newer heater shuts down and won’t relight Clogged air intake screen or tripped safety device (FVIR) Clean the intake screen; reset or call a pro (see below)
Keeps going out after new thermocouple Failing gas control valve Professional replacement

1. Faulty thermocouple

The thermocouple is a thin copper rod with its tip in the pilot flame. When heated, it produces a tiny electrical current that tells the gas valve the pilot is lit. If it’s worn, dirty or bent away from the flame, the valve shuts the gas off and the pilot dies as soon as you release the knob. Lennox notes this is one of the most common reasons a pilot keeps going out.

  • Check the position: the tip should sit in the top part of the pilot flame.
  • Clean it: with the gas off and the part cool, lightly clean soot from the tip with fine sandpaper or steel wool.
  • Replace it: thermocouples are inexpensive, and Angi estimates a DIY replacement costs about $5 to $20 in parts and takes about an hour. Use one of the same length. Step-by-step instructions are in how to replace a thermocouple on a water heater.

2. Dirty pilot tube or burner

Dust, soot or rust can partly block the pilot orifice, giving a weak flame that doesn’t heat the thermocouple enough. A healthy pilot flame is steady and blue; a yellow or flickering flame suggests a dirty orifice or poor air mix. With the gas fully off, clean the opening with compressed air or a thin brush. Don’t use water or liquid cleaners on gas parts.

3. Drafts and poor airflow

A breeze from an open door, window, vent or furnace fan can blow out the pilot. Keep the area around the heater clear, close the burner access cover properly, and check that the flue and vent aren’t blocked.

4. Clogged air intake on newer (FVIR) heaters

Gas water heaters sold in the US since the mid-2000s are “flammable vapor ignition resistant” (FVIR). They draw combustion air through a screen near the bottom and have a safety device that shuts the heater down if the burner chamber overheats. If the intake screen gets clogged with dust or lint, the burner can starve for air and overheat, tripping the safety device.

  • Clean the intake screen regularly with a soft brush or vacuum, more often in dusty or linty areas like laundry rooms and garages.
  • Some models have a resettable thermal switch; others use a one-time thermal device that a technician must replace. Check your manual.
  • If it keeps tripping, have the venting and combustion air checked by a pro.

5. Gas supply or gas valve problems

  • Check other gas appliances. If they don’t work either, the problem is the supply; contact your gas company.
  • Make sure the gas valve on the supply line is fully open (handle parallel to the pipe).
  • A failing gas control valve can cut the pilot even with a good thermocouple. It needs professional replacement and can be expensive, so weigh it against the heater’s age; see how long water heaters last.

How to relight a water heater pilot

  1. Turn the gas control knob to “Off” and wait about 5 minutes for any gas to clear.
  2. Turn the knob to “Pilot.”
  3. Press and hold the knob (or pilot button) and press the igniter until the pilot lights.
  4. Keep holding for about 30 to 60 seconds so the thermocouple heats up, then release.
  5. If the pilot stays lit, turn the knob to “On.” If it goes out, see the causes above.

Electronic ignition heaters work differently; see how to light a water heater with an electronic pilot. Confused by the “Pilot” setting? See what is pilot mode?

Repair or replace?

A thermocouple, pilot assembly or intake cleaning is a cheap fix. A new gas control valve on a heater that’s 10 or more years old is often better spent toward a new heater. See water heater replacement cost and our full water heater troubleshooting guide.

Water heater thermocouples on Amazon →  |  Gas leak detectors →

Frequently asked questions

Why does my pilot light go out when I let go of the button?

Almost always the thermocouple: it isn’t sensing the flame because it’s dirty, worn or out of position. Hold the knob a little longer (up to a minute); if it still goes out, clean or replace the thermocouple.

How much does it cost to fix a pilot light that won’t stay lit?

A DIY thermocouple replacement costs about $5 to $20 in parts. A professional service call costs more; Angi puts typical water heater repairs at about $220 to $985 depending on the problem.

Is it dangerous if my pilot light keeps going out?

The thermocouple is a safety device that shuts off the gas when the pilot is out, so it’s designed to fail safe. But if you smell gas, leave and call the gas company.

Can a dirty air filter or lint make the pilot go out?

On newer FVIR heaters, yes: a clogged combustion air intake screen can starve the burner and trip the heater’s safety shutoff.

Sources: Lennox “Water heater pilot light keeps going out,” Angi thermocouple replacement guide, Water Heater Rescue FVIR troubleshooting notes, A.O. Smith guidance. Gas appliance repairs can be dangerous; call a licensed professional if you’re unsure.

Leave a Comment