Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.
To change a refrigerator water filter, find the filter (usually in the upper right inside corner, behind the base grille, or inside a door), twist the old one counterclockwise or press its release button, then push in the new filter and turn it clockwise until it locks. Run 1.5 to 4 gallons of water through the dispenser to flush out air and carbon dust, then hold the filter reset button for about 3 seconds. Most manufacturers recommend a new filter about every 6 months.
Quick steps (most brands)
- Check the replacement filter model printed on the old filter or in your manual
- Turn off the ice maker and put a towel under the filter
- Remove the old filter: twist left (counterclockwise) or press the eject button
- Remove the cap from the new filter, insert it and twist right until it locks
- Flush: dispense water until it runs clear (see your brand below for how much)
- Reset the filter light: hold the reset or filter button for about 3 seconds
Refrigerator water filter by brand
| Brand | Where the filter usually is | Flush | Reset the light |
|---|---|---|---|
| Samsung | Upper right inside, behind a cover, or in the base grille | Several gallons | Hold Filter Reset 3 seconds (Family Hub: Fridge Manager app) |
| LG | Inside the fresh food section (top or back left), or behind the bottom door bin | About 2.5 gallons | Hold Water Filter or Filter Reset 3 seconds |
| Whirlpool, Maytag, KitchenAid | Upper right inside, or the base grille | About 4 gallons | Hold the filter button until it beeps |
| Frigidaire | Upper right inside, or behind the base grille | About 1.5 gallons (3 minutes) | Hold reset 3 to 5 seconds |
| GE | Top left inside, inside the left door (RPWFE), or the ceiling | 1 to 2 gallons | RPWFE resets itself; others in the control panel |
From each manufacturer’s support pages, November 2026. Locations and buttons vary by model; check your owner’s manual.
How to change a Samsung refrigerator water filter
- Turn off the water supply if your manual says to, and open the filter cover.
- Turn the old filter counterclockwise to unlock it and pull it out.
- Remove the cap from the new filter, insert it, and turn it clockwise until the lock symbol lines up with the indicator line.
- Dispense several gallons of water to clear air and particles.
- Reset the filter light: press and hold Filter Reset for 3 seconds. On Family Hub models, go to Apps, Fridge Manager, Fridge Settings, Water Filter, then tap Reset. On models with arrow buttons, go to More Options, then Filter Reset.
Samsung’s filter light runs on a 6-month timer. Common filters include the HAF-CIN, HAF-QIN and HAFCU1.
How to change an LG refrigerator water filter
- Close the water supply valve if possible and press the dispenser to release pressure, with a cup underneath.
- Reach the filter: depending on the filter type, remove the top shelf and lamp cover, the bottom door bin, or a filter cover.
- Remove the old filter (most twist; some pull straight out).
- Remove the cap from the new filter, align its tabs, push it in and turn it until the lock mark lines up.
- Reopen the water and dispense about 2.5 gallons, or run water for 30 seconds on, 60 seconds off for 5 minutes.
- Reset: hold the Water Filter or Filter Reset button for 3 seconds until it chimes.
Common LG filters include the LT500P, LT600P, LT700P, LT800P and LT1000P.
How to change a Whirlpool refrigerator water filter
Whirlpool (and Maytag, KitchenAid and Amana) use four main filter styles:
- Filter 1 (upper right inside or base grille): push and twist to remove and install; no tools needed.
- Filter 2 (upper right inside): turn the old filter left to remove it. Push the new one in and turn it clockwise until it locks.
- Filter 3 (left side of the base grille): press the eject button to pop the old filter out, then push the new one in until the button pops back out.
- Filter 4 (upper right inside): turn the old filter left to remove it, then push the new one up to lock it. On a first install, remove the cap from the slot.
Before installing, take the protective covers off the O-rings and check they’re in place; missing O-rings are a common cause of leaks. Run about 4 gallons through the dispenser. To reset, hold the filter button on the dispenser or ceiling control panel until it beeps. Common filters include the EveryDrop filters 1, 2, 3 and 4.
How to change a Frigidaire refrigerator water filter
- Turn off the ice maker.
- Find the filter in the upper right corner inside or behind the base grille.
- Push to release or twist to unlock, depending on the model. Don’t force a stuck filter.
- Install the new filter the same way until it clicks or locks.
- Run water for about 3 minutes (about 1.5 gallons).
- Reset: hold the reset button for 3 to 5 seconds until the light goes off.
Common Frigidaire filters include PureSource Ultra and PureSource Ultra II.
How to change a GE refrigerator water filter
- XWF, XWFE, MWF: turn the old filter left while pulling down gently. Fill the top of the new filter with water, align the arrow, push it up and turn right until it stops.
- RPWFE: open the filter door, swing the cartridge out, turn a quarter turn counterclockwise and pull it out. Insert the new one with “FRONT” facing up, turn a quarter turn clockwise and swing it back in. The red indicators should not be visible.
Dispense 1 to 2 gallons; sputtering at first is normal. GE says filters last about 6 months or about 170 to 200 gallons. The RPWFE filter has an RFID chip that resets the reminder automatically and can’t be reset manually; GE says non-genuine filters without the chip can trigger a “Leak Detected” message.
Genuine or compatible filters?
Genuine filters fit exactly and are certified for what they remove. Compatible filters are cheaper but vary in quality and certification; Samsung and GE warn that non-genuine filters can leak or not be recognized. Whichever you choose, look for NSF/ANSI 42 and 53 certification and, for PFAS or lead, check the filter’s certified claims. See our guide to the best refrigerator water filters.
Samsung filters on Amazon → | LG → | Whirlpool EveryDrop → | Frigidaire → | GE →
Troubleshooting after a filter change
- Water sputters: normal air in the line; keep dispensing.
- Leaking: the filter isn’t fully locked or an O-ring is missing. Remove it and reinstall.
- Slow or no water: the filter may not be seated; try reinstalling, and check the water supply valve.
- Cloudy water: usually tiny air bubbles that clear in a minute; keep flushing.
- Light still on: hold the reset button longer, or check the manual for your model’s reset steps.
Frequently asked questions
How often should I change my refrigerator water filter?
About every 6 months, or sooner if water flow slows, ice tastes bad, or you have hard water.
How do I reset the water filter light on a Samsung refrigerator?
Press and hold the Filter Reset button for 3 seconds. On Family Hub models, reset it in the Fridge Manager app on the screen.
Do I need to turn off the water to change a fridge filter?
Usually not; most filters seal automatically. Some manuals, like Samsung’s and LG’s, suggest closing the supply valve first.
What happens if I don’t change my fridge water filter?
Flow slows, taste and odor get worse, and an overused filter stops removing contaminants effectively.
Sources: Samsung US support “How to replace the water filter in a Samsung refrigerator”; LG US help library “How to replace the water filter in your LG refrigerator”; Whirlpool “How to replace refrigerator water filters”; Frigidaire “How to change your refrigerator filter”; GE Appliances support articles on replacing water filters and RPWFE operation. Steps vary by model.