Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.
To install a whole-house water filter, choose a spot on the main water line after the shutoff valve (and after the pressure tank on a well), turn off the water, cut the pipe, fit shutoff valves and a bypass, mount the filter housings and connect them with the flow arrow pointing toward the house. Then restore water slowly, check for leaks and run the taps to purge air. It’s a moderate DIY job if you can cut and join pipe; otherwise a plumber can usually do it in a few hours. An under-sink filter is much easier and usually needs no pipe cutting.
Before you start
- Location: on the main line where it enters the house, protected from freezing, with room below to change cartridges
- Order: sediment filter first, then carbon; install before the water heater and, usually, before a softener
- Valves: a shutoff before and after the filter plus a bypass so the house keeps water during cartridge changes
- Electrical ground: if your metal water pipe grounds the electrical system, add a grounding jumper across the filter; ask an electrician if unsure
- Code: check whether your area requires a permit or licensed plumber
Tools and materials
- Whole-house filter system (housings, cartridges, mounting bracket, housing wrench)
- Shutoff valves and a bypass valve (or three-valve bypass loop)
- Pipe cutter, plus fittings for your pipe type (push-to-connect, PEX crimp or solder fittings for copper)
- Thread-seal tape, pipe wrenches, drill and screws, bucket and towels
- Grounding jumper clamp kit (if your plumbing grounds the electrical system)
Whole-house filter systems on Amazon → | Grounding jumper kits →
How to install a whole-house water filter, step by step
- Pick the location. Near where the main line enters, in an accessible spot protected from freezing, with space to change filters.
- Shut off the water at the main valve, open the lowest faucets to drain the lines and relieve pressure.
- Mount the bracket to the wall (add a plywood backer if needed) so the housings hang level and the pipe isn’t carrying their weight.
- Cut the main line with a tubing cutter, making clean, straight cuts, and remove the section where the filter goes.
- Fit the valves: install a shutoff on each side of the filter and a bypass valve so water can reach the house while the filter is serviced.
- Connect the housings, following the IN and OUT markings so water flows toward the house. Seal threaded joints with tape. If you solder copper, do it away from plastic housings so heat doesn’t melt them.
- Add the grounding jumper across the filter if the plumbing is part of your electrical ground.
- Insert cartridges (sediment first, carbon second) and tighten the housings by hand, then a quarter turn with the wrench.
- Restore water slowly, check every joint for leaks and run faucets until the air and carbon fines clear.
Based on This Old House’s whole-house filter installation guide and manufacturer instructions.
How to install an under-sink water filter
- Turn off the cold water valve under the sink and open the faucet to relieve pressure.
- Mount the filter head or housing to the cabinet wall, leaving room below to change the cartridge.
- Connect the feed adapter (usually a tee on the cold valve) and run the inlet tubing to the filter.
- For a dedicated faucet, drill or use an existing hole in the sink or countertop and connect the outlet tubing. In-line models connect straight to the existing cold line instead.
- Insert the cartridge, turn the water on slowly, check for leaks and flush as the instructions direct.
Our best under-sink water filters guide covers which models are easiest to install.
How often to change the filters
| Cartridge | Typical interval |
|---|---|
| Sediment prefilter | Every 3 to 6 months |
| Carbon filter | Every 6 to 12 months |
| Under-sink carbon or combo | Per the maker’s gallon rating, often 6 to 12 months |
Intervals from This Old House; replace sooner if pressure drops or taste and odor return.
DIY or hire a plumber?
If you’re comfortable cutting pipe and using push-to-connect or PEX fittings, a whole-house filter is a reasonable weekend project. Soldering copper, working on a well system, or adding a grounding jumper are good reasons to hire a plumber. Not sure which system you need? Start with our whole-house water filter guide and home water filtration guide, and test your water first with a water test kit.
Frequently asked questions
Where should a whole-house filter be installed?
On the main line after the main shutoff (and after the pressure tank on a well), before the water heater. Most installers put it before a water softener so sediment doesn’t foul the softener resin.
Do I need a bypass valve?
It’s strongly recommended. It keeps water flowing to the house while you change cartridges or service the filter.
Will a whole-house filter lower water pressure?
Slightly, and more as cartridges clog. Choosing a large housing (such as 4.5 x 20 inch) and changing cartridges on time keeps pressure up.
How long does installation take?
Typically a few hours for a plumber or experienced DIYer; an under-sink filter often takes under an hour.
Sources: This Old House “How to Install a Whole-House Water Filter”; manufacturer installation manuals. Check local plumbing and electrical codes.