Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.
A water heater expansion tank is a small tank, usually 2 to 5 gallons, installed on the cold water line to absorb the extra volume water takes up when it’s heated. You need one if your home has a “closed” plumbing system, which happens when there’s a check valve, backflow preventer or certain pressure-reducing valves on the main water line, and many local codes now require one with any new water heater. Without it, pressure spikes can make the relief valve drip and strain the heater, pipes and fixtures.
Expansion tanks at a glance
- Needed when: your system is closed (check valve or backflow preventer on the main) or local code requires it
- Size: often 2 to 4.5 gallons for a 40 to 50-gallon heater, depending on pressure and system volume
- Pre-charge: set the tank’s air pressure to match your home water pressure (often 50 to 60 psi)
- Cost: about $150 to $450 installed (Angi; national average about $325)
- Lifespan: about 5 to 10 years (A.O. Smith)
What does a water heater expansion tank do?
Water expands as it heats. In an “open” system, that extra water can push back into the city main. But if a check valve or backflow preventer stops it, the pressure has nowhere to go. An expansion tank has an air cushion separated from the water by a rubber diaphragm or bladder. As the heater warms the water, the extra volume pushes into the tank and compresses the air, keeping household pressure steady.
Do you need an expansion tank?
- Yes, if your plumbing is a closed system: there’s a check valve, backflow preventer or a pressure-reducing valve with a built-in check on the main line. A.O. Smith notes many codes now require an expansion tank wherever a backflow preventer is present.
- Yes, if local code requires it: for example, the California Plumbing Code (Section 608.3) requires thermal expansion control on water heating systems. Many US cities have similar rules, so ask your local building department or plumber.
- Maybe, if you have these symptoms: a temperature and pressure (T&P) relief valve that drips after the heater runs, banging pipes, or pressure that swings.
Signs you need one (or yours has failed)
- The T&P relief valve drips or discharges regularly
- Water hammer (banging or knocking pipes)
- Uneven water pressure
- Frequent leaks at fixtures or toilet fill valves
- A tank that sounds full of water when tapped, or water at the air valve: the diaphragm has likely failed (A.O. Smith)
A dripping relief valve can also come from other problems; see our water heater troubleshooting guide.
How to size an expansion tank
A.O. Smith explains that sizing depends on the water heater’s capacity, your incoming water pressure and total system volume, and that the tank doesn’t need to match the heater’s size. A 50-gallon heater may need only a 2 or 4.5-gallon expansion tank. Manufacturers publish sizing charts; higher water pressure needs a larger tank. Oversizing costs more and takes space; undersizing won’t absorb the expansion.
| Water heater | Typical expansion tank |
|---|---|
| 40 to 50 gallons, normal pressure | About 2 gallons |
| 40 to 50 gallons, higher pressure (80 psi) | About 4.5 gallons |
| 75 to 80 gallons | About 4.5 gallons or larger |
Typical examples only; always use the tank manufacturer’s sizing chart for your pressure and heater size.
Installing an expansion tank
- Check your house pressure with a gauge on an outdoor spigot or the heater drain. If it’s above 80 psi, ask a plumber about a pressure-reducing valve.
- Set the tank’s pre-charge to match house pressure using a tire pump and gauge on the tank’s air valve before installing (A.O. Smith says typical residential pressure is 50 to 60 psi).
- Install it on the cold water supply line near the water heater, between the shutoff valve and the heater.
- Support the tank with a strap or bracket; a full tank is heavy and shouldn’t hang only on the pipe.
- Use thread sealant, open the water, check for leaks and test the relief valve.
Many areas require a permit for water heater work. If you’re replacing your heater, ask the installer to include the expansion tank in the quote; see water heater replacement cost and Lowe’s vs Home Depot installation.
Maintenance
- Check the pre-charge about once a year (water off and pressure relieved first).
- If water comes out of the air valve, the diaphragm has failed: replace the tank.
- Replacement is usually more cost-effective than repair.
Thermal expansion tanks on Amazon → | Water pressure gauges →
Frequently asked questions
Is an expansion tank required for a water heater?
It depends on your plumbing and local code. It’s required or strongly recommended for closed systems, and many jurisdictions require one with any new water heater installation.
Where does the expansion tank go?
On the cold water supply line near the water heater, usually above or beside it.
What pressure should an expansion tank be set to?
The same as your home’s water pressure, often 50 to 60 psi. Check with a gauge before installing.
How long does an expansion tank last?
About 5 to 10 years, depending on water quality and how often the heater cycles.
Sources: A.O. Smith guide to expansion tanks, City of Roseville thermal expansion tank requirements (California Plumbing Code 608.3), Angi expansion tank cost data. Follow local code and the tank manufacturer’s sizing chart.