Water Heater Anode Rod: Types, When to Replace It and How

Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

An anode rod is a metal rod inside a tank water heater that corrodes on purpose so the steel tank doesn’t. It’s usually made of magnesium, aluminum or an aluminum/zinc alloy. Once it’s used up, the tank itself starts to rust and eventually leaks, so checking and replacing the anode is one of the cheapest ways to make a water heater last longer. A.O. Smith recommends inspecting it once a year.

Anode rods at a glance

  • Job: a “sacrificial” anode that protects the tank from corrosion
  • Check: about once a year (A.O. Smith); more often with softened or very hard water
  • Replace: when much of the rod is eaten away and the steel core wire is showing
  • Rotten egg smell from hot water only? Swap a magnesium anode for aluminum/zinc or a powered anode
  • Tankless heaters don’t use anode rods

How does an anode rod work?

Water in a tank slowly corrodes metal. The anode rod is made of a more “active” metal than the steel tank, so corrosion attacks the rod first. As long as there’s enough anode left, the glass-lined steel tank is protected. A.O. Smith notes that how long the rod lasts depends on your water chemistry, how much hot water you use and whether you have a water softener.

Types of anode rods

Type Pros Cons Best for
Magnesium Strong protection; standard in many heaters Wears faster in soft water; can cause rotten egg smell with sulfate-rich water Most city water
Aluminum Lasts longer in hard water; cheaper Less protection in very soft water Hard water
Aluminum/zinc Helps stop sulfur (“rotten egg”) odor Slightly less protective than magnesium Wells or water with sulfur smell
Powered (impressed current) Doesn’t wear out; stops odor; good with softened water Costs more; needs a power outlet Odor problems, softened water, long-term ownership
Flexible / segmented Fits where there’s little overhead clearance Same metals as above Tight spaces

Signs your anode rod needs replacing

  • Rotten egg smell from the hot water only
  • Rusty or discolored hot water
  • The heater is several years old and the rod has never been checked
  • Popping noises with heavy sediment (worn anodes can add debris)

Rusty water from an older heater can also mean the tank itself is corroding; see signs your water heater is going bad.

How to check and replace an anode rod

  1. Turn off power (electric) or set the gas control to “Pilot” or “Off.”
  2. Close the cold water supply and open a hot tap to relieve pressure.
  3. Drain a few gallons from the drain valve so the water level is below the anode port. See how to flush a water heater.
  4. Find the anode: usually a hex head on top of the tank (sometimes under a plastic cap) or combined with the hot outlet nipple.
  5. Loosen it with a 1-1/16 inch socket and breaker bar. It’s often very tight; brace the tank so it doesn’t twist.
  6. Inspect it: if the rod is heavily pitted, thin, or the steel core wire is exposed over a good part of its length, replace it.
  7. Install the new rod with plumber’s tape on the threads, refill the tank (open a hot tap until water flows steadily), check for leaks and restore power or gas.

Low ceiling? Use a flexible segmented anode. Never turn on an electric heater before the tank is full; see how to turn a water heater on safely.

Anode rods and rotten egg smell

If only your hot water smells like rotten eggs, North Dakota State University Extension explains that sulfates in the water can react with a magnesium anode to form hydrogen sulfide gas. Replacing it with an aluminum/zinc or powered anode usually fixes the odor. Don’t just remove the anode: the tank will corrode quickly, and it may affect your warranty. More in our water heater troubleshooting guide.

Do water softeners affect anode rods?

Yes. A.O. Smith lists water softeners as a factor in anode life; softened water tends to consume anodes faster, so check the rod more often if you have a softener. See water softener vs water filter.

Magnesium anode rods on Amazon →  |  Aluminum/zinc →  |  Powered anodes →

Frequently asked questions

How often should I replace my water heater anode rod?

Inspect it about once a year and replace it when it’s mostly consumed. How long it lasts depends on water chemistry, hot water use and whether you soften your water.

Can I replace an anode rod myself?

Yes, if you can drain a few gallons and break loose a tight fitting. A plumber can do it if the rod is seized or space is tight.

Which anode rod is best?

Magnesium for most city water, aluminum or aluminum/zinc for hard water or sulfur odor, and a powered anode for long-term protection or softened water.

Do tankless water heaters have anode rods?

No. Tankless units don’t store water, so they don’t need one, but they need regular descaling instead.

Sources: A.O. Smith water heater maintenance guidance (anode rod inspection), North Dakota State University Extension (rotten egg odor from hot water). Work on gas and electric heaters can be dangerous; call a licensed plumber if you’re unsure.

Leave a Comment