Water Heater Popping, Rumbling or Kettling? Causes and Fixes

Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

A water heater that pops, rumbles or crackles like popcorn is usually “kettling”: sediment has built up on the bottom of the tank, and water trapped under it boils and bursts through. It’s most common with hard water and on gas heaters. The fix is to flush the tank to remove the sediment, and to flush it every year after that. Other noises mean different things: humming and light ticking are normal, while hissing, sizzling or screeching can signal a leak or pressure problem that needs attention.

Quick answer by sound

  • Popping, rumbling, kettling: sediment; flush the tank
  • Humming (electric): normal element operation
  • Ticking or clicking: usually normal pipe expansion
  • Hissing, sizzling, crackling: possible leak onto the burner or element; turn off power or gas and call a pro
  • Screeching or whistling: a partly closed valve or pressure problem
  • Banging when taps close: water hammer in the pipes

Water heater noises and what they mean

Noise Likely cause Normal? What to do
Popping, rumbling Sediment on the tank bottom, heated under the debris No Flush the tank; flush yearly
Kettling (like a kettle about to boil) Heavy sediment or scale; overheating at the bottom No Flush or descale; check the thermostat
Humming Electric heating elements running Yes None needed
Ticking, clicking Heat traps or pipes expanding Yes, if light None needed
Crackling, sizzling, hissing Water hitting a gas burner, or a leaking element gasket No Turn off power or gas and call a pro
Screeching, whistling Partly closed valve, faulty T&P valve, high pressure No Open valves fully, check pressure
Knocking, banging Water hammer in the plumbing Not the heater Water hammer arrestor, lower pressure, secure pipes
Gurgling Water moving after heavy use Yes None needed

Based on Rheem’s guide to water heater noises.

Why sediment makes a water heater pop

Hard water contains calcium and magnesium that settle out as the water heats. Over time, a layer of sediment and scale forms on the bottom of the tank. On gas heaters, the burner heats the tank bottom; on electric heaters, the lower element can get coated or buried. Water trapped under the sediment overheats into steam bubbles that pop up through the layer, making the popping or rumbling sound.

Sediment also makes the heater work harder, wastes energy, can reduce hot water capacity, and can shorten the tank’s life. See what is hard water.

How to fix a popping water heater

  1. Turn off the heat. Set a gas heater to Pilot or Off; turn off the breaker on an electric heater.
  2. Shut off the cold water supply to the heater.
  3. Attach a garden hose to the drain valve and run it to a floor drain or outside. The water is hot.
  4. Open a hot water tap in the house to let air in, then open the drain valve.
  5. Flush: when the tank is mostly empty, briefly open the cold supply to stir up and push out sediment. Repeat until the water runs clear.
  6. Refill: close the drain, open the cold supply and let water run from the hot tap until it flows steadily with no air.
  7. Restore heat: only after the tank is full. Turning on an electric heater with an empty tank can burn out the elements.

Full steps: our water heater flushing guide and draining guide. If the drain valve clogs with sediment or the popping continues after flushing, a plumber can deep-clean or descale the tank.

Water heater flush kits on Amazon →  |  Brass drain valves →

How to prevent sediment noise

  • Flush the tank once a year, or every 6 months with very hard water.
  • Consider a water softener if your water is very hard; see how a water softener works.
  • Keep the temperature around 120°F; higher settings speed up scale.
  • Check the anode rod every 2 to 3 years.

When a noisy water heater needs replacing

If the tank still pops after a thorough flush, is more than 10 to 12 years old, and shows rust or leaks, replacement is often the better choice. Check its age with our serial number guide and see the replacement cost.

Tankless water heater noises

Tankless units can also make noise from scale in the heat exchanger, a whirring fan on gas models, or clicking from the igniter. Scale buildup often shows up with error codes; descale the unit as described in our tankless flushing guide.

Frequently asked questions

Is a popping water heater dangerous?

Usually not immediately, but it means sediment is stressing the tank and wasting energy. Flush it soon. Hissing or sizzling near the burner or element is more urgent.

Can a water heater explode from sediment?

Sediment alone rarely causes a dangerous failure, because the temperature and pressure relief valve protects the tank. Never cap or block that valve.

Why does my water heater make noise when the water is running?

Cold water rushing in can make ticking or popping sounds as metal cools and sediment stirs. A whistle while water runs often points to a partly closed valve.

How much does it cost to fix a noisy water heater?

Flushing yourself costs little; a plumber typically charges for a service call to flush or descale. Replacement is needed only if the tank is failing.

Sources: Rheem “The Ultimate Guide to Water Heater Noises”; manufacturer installation and maintenance manuals. Gas and electrical work should be done safely; consult a professional if unsure.

Leave a Comment