What Is Reverse Osmosis? How RO Systems Work, Pros and Cons

Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

Reverse osmosis (RO) is a water treatment method that pushes water through a semi-permeable membrane so fine that most dissolved contaminants can’t pass through. The clean water goes to a storage tank or a dedicated faucet, and the rejected contaminants are flushed down the drain. A home RO system can remove lead, nitrate, fluoride, arsenic and other dissolved solids, but it wastes some water, removes beneficial minerals and isn’t a standalone treatment for bacteria.

Reverse osmosis at a glance

  • How it works: household water pressure forces water through an RO membrane; contaminants leave in a reject stream
  • Removes: lead, nitrate, fluoride, sodium, sulfate, many dissolved metals and total dissolved solids
  • Doesn’t reliably remove: dissolved gases, many volatile organic chemicals (unless a carbon filter is included) and, on its own, bacteria
  • Water use: older systems can waste about 3 to 4 gallons per gallon made; EPA WaterSense-labeled systems waste about 2.3 gallons or less
  • Typical cost: $150 to $1,300 for an under-sink system installed, plus filter and membrane replacements

How does reverse osmosis work?

In natural osmosis, water moves through a membrane from a weaker solution to a stronger one. Reverse osmosis uses pressure to push water the opposite way: from the contaminated side, through the membrane, to the clean side. Dissolved salts, metals and other contaminants are too large to pass and are rinsed away in a “reject” or brine stream that goes to the drain.

Most under-sink RO systems use several stages:

  1. Sediment pre-filter: catches sand, rust and grit that would clog the membrane.
  2. Carbon pre-filter: removes chlorine (which damages many membranes) plus some taste, odor and chemical contaminants.
  3. RO membrane: does the main job, removing dissolved solids.
  4. Storage tank (on tank models): RO is slow, so treated water is stored until you open the faucet.
  5. Carbon post-filter: polishes taste on the way to the faucet.
  6. Optional remineralization stage: adds back calcium and magnesium for taste.

Tankless RO systems use a pump to filter water on demand, so they’re smaller and usually waste less water, but they need an electrical outlet under the sink.

What does reverse osmosis remove?

Contaminant Does RO remove it?
Lead, copper and other dissolved metals Yes, very effectively
Nitrate and nitrite Yes
Fluoride Yes
Arsenic Yes (works best on arsenic V; check certification)
Sodium, sulfate, chloride and total dissolved solids (TDS) Yes
Chlorine, taste and odor Yes, mainly through the carbon filters
PFAS (“forever chemicals”) Many systems, if certified for PFOA/PFOS reduction
Volatile organic chemicals (VOCs) Partly; depends on the carbon stages
Dissolved gases (such as radon, hydrogen sulfide) No
Bacteria and viruses Not recommended as the only treatment; disinfect first if you have a microbial problem

Based on University of Massachusetts Extension guidance on RO treatment. No membrane removes 100% of any contaminant; check the system’s certification for the specific contaminants you need to reduce.

Not sure what’s in your water? Start with a water test, then see our home water filtration guide to match the treatment to the problem.

Pros and cons of reverse osmosis

Pros Cons
Removes a wider range of dissolved contaminants than carbon filters alone Sends some water down the drain
Great-tasting drinking and cooking water Removes calcium and magnesium (some people add a remineralizing filter)
Cheaper per gallon than bottled water over time Slow; tank models can run low with heavy use
Fits under a kitchen sink Needs regular filter and membrane changes
Can be certified to NSF/ANSI 58 Usually treats only one tap, not the whole house

How much water does reverse osmosis waste?

Older or basic RO units may produce only about 1 gallon of treated water for every 4 gallons that enter, sending around 3 gallons to the drain. The EPA’s WaterSense specification for RO systems requires an efficiency of at least 30%, which works out to no more than about 2.3 gallons of reject water per gallon made. Many newer tankless systems advertise even better ratios. Look for the WaterSense label or a stated waste-to-pure ratio when you compare models.

How much does a reverse osmosis system cost?

Cost item Typical range
Under-sink or countertop system, installed $150 to $1,300
Professional installation (under-sink) About $150 to $300
Whole-house RO system About $1,000 to $4,800
Pre- and post-filters Every 6 months to 2 years
RO membrane $50 to $100 every 3 to 5 years

Ranges from This Old House’s reverse osmosis cost guide (updated March 2026). Prices vary by brand, filter count and location.

Do you need a reverse osmosis system?

  • Yes, probably, if a water test shows lead, nitrate, arsenic, fluoride or high TDS that you want to reduce in drinking water.
  • Maybe, if you buy a lot of bottled water or don’t like how your tap water tastes.
  • Probably not, if your only issue is chlorine taste (a carbon filter is enough) or hard-water scale (that’s a job for a water softener; see water softener vs water filter).
  • Treat the whole house differently: for sediment, chlorine or iron throughout the home, see our whole-house water filter guide. RO is usually added at the kitchen sink on top.

What to look for when buying an RO system

  1. Certification: NSF/ANSI 58 (RO systems), plus NSF/ANSI 53 or 401 claims for specific contaminants such as lead or PFAS. Check the certifier’s listing, not just the box.
  2. Efficiency: the WaterSense label or a waste ratio of about 2:1 or better.
  3. Tank or tankless: tankless saves space and water but needs power; tank models work during outages.
  4. Filter cost and availability: compare the yearly cost of replacement filters, not just the system price.
  5. Your water pressure: low pressure (below about 40 psi) slows production; some systems include a booster pump.

Compare under-sink RO systems on Amazon →  |  TDS meters →

How to maintain a reverse osmosis system

  • Replace the sediment and carbon filters on the maker’s schedule, often every 6 to 12 months.
  • Replace the membrane every 3 to 5 years, or sooner if a TDS meter shows the water quality dropping.
  • Sanitize the system and tank when you change filters, following the manual.
  • Keep a log of filter changes, and retest your water at least once a year.

Frequently asked questions

Is reverse osmosis water safe to drink?

Yes. RO water is widely used for drinking. It’s low in minerals, which affects taste more than safety for most people. If you’re concerned, choose a system with a remineralization stage or ask your health care provider.

Does reverse osmosis remove fluoride?

Yes, RO is one of the few home treatments that removes most fluoride.

Does reverse osmosis remove bacteria?

The membrane blocks many microorganisms, but RO is not recommended as the only treatment for bacteria. If your water has a microbial problem, use a certified disinfection method such as UV.

Is reverse osmosis better than a carbon filter?

For dissolved contaminants like lead, nitrate, fluoride and arsenic, yes. For chlorine taste and odor alone, a carbon filter is cheaper and wastes no water. Most RO systems include carbon filters anyway.

Can reverse osmosis soften water?

An RO system removes hardness minerals from the water it treats, but hard water can scale and shorten the membrane’s life. In very hard water, a softener ahead of the RO system protects it.

Sources: University of Massachusetts Extension (reverse osmosis treatment of drinking water supplies), NSF (how reverse osmosis works), US EPA WaterSense specification for point-of-use RO systems (2024), This Old House reverse osmosis system cost guide (March 2026). Treatment results depend on your water; test before and after installation.

Leave a Comment