Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.
Navien tankless water heaters and combi boilers show error codes starting with “E” on the front display. The ones homeowners see most are E003 (ignition failure), E012 (flame loss), E016 (heat exchanger overheating, often from scale), E030 (abnormal exhaust temperature) and E407/E421 (water temperature sensor faults). Simple causes such as a closed gas valve, a blocked vent or a dirty inlet filter can be fixed at home; sensor, fan, gas valve and circuit board faults need a licensed technician.
Before you start
- Reset: press the Reset button on the front panel (or turn power off and on). Some codes reset automatically when the problem clears.
- Smell gas? Leave immediately and call your gas company from outside.
- Repairs: internal parts and gas components should be serviced by a licensed professional.
Navien error codes chart
| Code | Meaning | What you can check | Call a pro if |
|---|---|---|---|
| E001 | Heat exchanger over temperature | Reset; make sure inlet valves are fully open | Repeats |
| E003 | Ignition failure | Gas supply valve open? Other gas appliances working? Propane tank not empty? Reset | Gas is fine and code persists |
| E004 | False flame detection | Always | |
| E012 | Flame loss | Check gas supply and that vents aren’t blocked; reset | Repeats |
| E016 | Overheating of heat exchanger | Flush/descale the heat exchanger; clean the inlet filter | Persists after flushing |
| E030 | Abnormal exhaust temperature | Check exhaust vent for blockage | Persists |
| E031 | Burner overheating | Always | |
| E046, E047 | Overheat sensor or exhaust thermostat fault | Check vents | Always |
| E060 | Dual venturi fault | Always | |
| E109 | Fan motor fault | Always | |
| E110 | Abnormal air pressure (often a vent or intake blockage) | Check intake and exhaust terminations for snow, ice, leaves or nests | Vent is clear and code persists |
| E407 | Hot water outlet thermistor open or shorted | Always | |
| E421 | Cold water inlet thermistor open or shorted | Always | |
| E434 | Water adjustment valve fault | Always | |
| E439 | Flow sensor fault | Clean the cold water inlet filter | Persists |
| E445 | Bypass mixing valve fault | Always | |
| E515 | Circuit board (PCB) fault | Power off and on | Persists |
| E517 | DIP switch setting error | Always (settings must match gas type and model) | |
| E594 | EEPROM (memory) fault | Power off and on | Persists |
Code meanings from Navien’s user and installation manuals. Combi boilers (NCB, NFC) also show heating-system codes such as E205, E218, E351 and E352 for heating thermistors, make-up water and system pressure. Codes and fixes vary by model; check your manual.
The most common Navien codes explained
E003: ignition failure
The heater tried to light and couldn’t. Most often the gas supply valve is closed, gas pressure is low, the propane tank is empty, or there’s air in a new gas line. Confirm other gas appliances work, then press Reset. If E003 keeps coming back, a technician should check gas pressure, the igniter and the flame rod.
E012: flame loss
The burner lit but lost its flame during operation. Low gas pressure, strong wind on the vent termination, a blocked vent or a dirty flame rod are typical causes.
E016: heat exchanger overheating
Usually a sign of scale buildup restricting water flow through the heat exchanger, especially with hard water. Flushing the heat exchanger and cleaning the inlet filter often clears it. If it returns soon after flushing, consider a water softener or scale inhibitor; see water softener vs water filter.
E030 and E110: exhaust and air problems
Check that the intake and exhaust pipes outside aren’t blocked by snow, ice, debris or nests, and that vent pipes haven’t come apart. If everything is clear, the venting design or fan may need professional attention.
E407 and E421: temperature sensor faults
These mean the outlet or inlet water thermistor reads open or shorted. The sensor or its wiring needs testing and replacement by a technician.
How to flush a Navien tankless water heater
- Turn off the power and close the gas supply valve.
- Close the cold and hot water isolation valves.
- Attach hoses to the service ports and connect a small pump in a bucket of descaling solution or white vinegar.
- Open the service ports and circulate for about 45 to 60 minutes, or as your manual specifies.
- Rinse with clean water, clean the cold water inlet filter, close the ports and restore water, gas and power.
Some Navien models include a built-in recirculation pump or scale indicator; follow your model’s instructions. More detail: how to flush a tankless water heater.
Tankless flush kits on Amazon → | Scale inhibitors →
Frequently asked questions
How do I reset my Navien tankless water heater?
Press the Reset button on the front panel. If there’s no reset option, turn the power off for a minute and back on. If the code returns, call for service.
What does E003 mean on a Navien?
Ignition failure. Check that the gas is on and supplied, then reset. Persistent E003 needs a technician.
What causes E016 on a Navien?
Overheating of the heat exchanger, most often from scale buildup or restricted water flow. Flushing and cleaning the inlet filter usually helps.
Can I fix Navien error codes myself?
You can check gas supply, vents, the inlet filter and do flushing. Sensors, fan, gas valve and circuit board faults should be handled by a licensed technician.
Sources: Navien user’s information and installation manuals (error code tables). Gas appliance repairs should be done by qualified technicians. Codes and procedures vary by model.