Navien Error Codes: What They Mean and How to Fix Them

Disclosure: As an Amazon Associate, Sweet Home Advisor earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

Navien tankless water heaters and combi boilers show error codes starting with “E” on the front display. The ones homeowners see most are E003 (ignition failure), E012 (flame loss), E016 (heat exchanger overheating, often from scale), E030 (abnormal exhaust temperature) and E407/E421 (water temperature sensor faults). Simple causes such as a closed gas valve, a blocked vent or a dirty inlet filter can be fixed at home; sensor, fan, gas valve and circuit board faults need a licensed technician.

Before you start

  • Reset: press the Reset button on the front panel (or turn power off and on). Some codes reset automatically when the problem clears.
  • Smell gas? Leave immediately and call your gas company from outside.
  • Repairs: internal parts and gas components should be serviced by a licensed professional.

Navien error codes chart

Code Meaning What you can check Call a pro if
E001 Heat exchanger over temperature Reset; make sure inlet valves are fully open Repeats
E003 Ignition failure Gas supply valve open? Other gas appliances working? Propane tank not empty? Reset Gas is fine and code persists
E004 False flame detection   Always
E012 Flame loss Check gas supply and that vents aren’t blocked; reset Repeats
E016 Overheating of heat exchanger Flush/descale the heat exchanger; clean the inlet filter Persists after flushing
E030 Abnormal exhaust temperature Check exhaust vent for blockage Persists
E031 Burner overheating   Always
E046, E047 Overheat sensor or exhaust thermostat fault Check vents Always
E060 Dual venturi fault   Always
E109 Fan motor fault   Always
E110 Abnormal air pressure (often a vent or intake blockage) Check intake and exhaust terminations for snow, ice, leaves or nests Vent is clear and code persists
E407 Hot water outlet thermistor open or shorted   Always
E421 Cold water inlet thermistor open or shorted   Always
E434 Water adjustment valve fault   Always
E439 Flow sensor fault Clean the cold water inlet filter Persists
E445 Bypass mixing valve fault   Always
E515 Circuit board (PCB) fault Power off and on Persists
E517 DIP switch setting error   Always (settings must match gas type and model)
E594 EEPROM (memory) fault Power off and on Persists

Code meanings from Navien’s user and installation manuals. Combi boilers (NCB, NFC) also show heating-system codes such as E205, E218, E351 and E352 for heating thermistors, make-up water and system pressure. Codes and fixes vary by model; check your manual.

The most common Navien codes explained

E003: ignition failure

The heater tried to light and couldn’t. Most often the gas supply valve is closed, gas pressure is low, the propane tank is empty, or there’s air in a new gas line. Confirm other gas appliances work, then press Reset. If E003 keeps coming back, a technician should check gas pressure, the igniter and the flame rod.

E012: flame loss

The burner lit but lost its flame during operation. Low gas pressure, strong wind on the vent termination, a blocked vent or a dirty flame rod are typical causes.

E016: heat exchanger overheating

Usually a sign of scale buildup restricting water flow through the heat exchanger, especially with hard water. Flushing the heat exchanger and cleaning the inlet filter often clears it. If it returns soon after flushing, consider a water softener or scale inhibitor; see water softener vs water filter.

E030 and E110: exhaust and air problems

Check that the intake and exhaust pipes outside aren’t blocked by snow, ice, debris or nests, and that vent pipes haven’t come apart. If everything is clear, the venting design or fan may need professional attention.

E407 and E421: temperature sensor faults

These mean the outlet or inlet water thermistor reads open or shorted. The sensor or its wiring needs testing and replacement by a technician.

How to flush a Navien tankless water heater

  1. Turn off the power and close the gas supply valve.
  2. Close the cold and hot water isolation valves.
  3. Attach hoses to the service ports and connect a small pump in a bucket of descaling solution or white vinegar.
  4. Open the service ports and circulate for about 45 to 60 minutes, or as your manual specifies.
  5. Rinse with clean water, clean the cold water inlet filter, close the ports and restore water, gas and power.

Some Navien models include a built-in recirculation pump or scale indicator; follow your model’s instructions. More detail: how to flush a tankless water heater.

Tankless flush kits on Amazon →  |  Scale inhibitors →

Frequently asked questions

How do I reset my Navien tankless water heater?

Press the Reset button on the front panel. If there’s no reset option, turn the power off for a minute and back on. If the code returns, call for service.

What does E003 mean on a Navien?

Ignition failure. Check that the gas is on and supplied, then reset. Persistent E003 needs a technician.

What causes E016 on a Navien?

Overheating of the heat exchanger, most often from scale buildup or restricted water flow. Flushing and cleaning the inlet filter usually helps.

Can I fix Navien error codes myself?

You can check gas supply, vents, the inlet filter and do flushing. Sensors, fan, gas valve and circuit board faults should be handled by a licensed technician.

Sources: Navien user’s information and installation manuals (error code tables). Gas appliance repairs should be done by qualified technicians. Codes and procedures vary by model.

Leave a Comment